The Nutribullet is one of a new series of tiny blenders with a cup like a pitcher.
It makes it simple to make smoothies with you on the go. The magic bullet blender’s design seeks to get the most out of your meal.
After blending a fantastic smoothie, you must remember to clean the blender before using it again. Yet, not everyone enjoys washing; they use the dishwasher.
Can the Nutribullet blade go in the dishwasher? This article will provide you with the most up-to-date information. Let’s get started!
Can The Nutribullet Blade Go In The Dishwasher?
The short answer is yes. Cups, lids, blades, and rims of the best Nutribullet blender are dishwashing safe on the top shelf. You can put these components in the dishwasher for years without issue.
To avoid junk becoming stuck underneath the fan blades, set it on the top rack of the dishwasher and rinse it off before putting it in.
Extreme heat can warp the plastic on the Nutribullet cup and accessories. So, we recommend avoiding sterilizing or using the dishwasher in cleaning mode.
If the rubber ring becomes loose when mixing, it can slip off, so keep a watch on it in the dishwasher.
How To Clean The Nutribullet Blender?
The Nutribullet is a simple-to-clean blender, so you can clean it in many ways.
This blender is so popular because it doesn’t require much cleaning, and you can consume your smoothie right from the same container.
Yet, it would be ideal if you cleaned it in the dishwasher. Fortunately, some pieces of the Nutribullet are dishwasher safe.
According to the manual, with a little soap and effort, you can remove any residual food and materials from the blender.
Cleaning the cup, power base, and blade completely, but, will ensure that you are blending food with clean equipment.
Cleaning The Blade
Cleaning the blade and cups of your Nutribullet may be a challenge, but it isn’t.
Although this process is simple, you should be cautious as this part is sharp.
Always unplug the Nutribullet blender from the power source before cleaning or assembling it.
It’s worth noting that, unlike the cup, the blade is not dishwasher safe. According to the instructions, you should wash it in warm, soapy water.
Of course, there are various ways to clean your extractor and blade, but hand washing is the most effective. Here are the step-by-step instructions:
- Remove the blade from the cup.
- Hand-wash with warm, soapy water
- Remove dirt from the blender blade with a dish brush or a stiff sponge.
- Make sure the blade is clean.
- Rinse with diluted lemon juice or vinegar for a thorough cleaning.
- Allow to air dry away from locations prone to moisture, such as your kitchen sink.
- Keep it in the kitchen cabinets.
Cleaning The Cups
You can either hand-wash cups or place them on the top shelf of the dishwasher. Hand-washing different elements of the blender are always safe.
Run warm water over the pieces and scrub the interior and exterior with dish soap and a sponge.
Avoid utilizing the Nutribullet’s sterilizing cycle or immersing parts of it in boiling water.
Using a dry rag, wipe the cup and blade’s outside and interior surfaces. Place them on a drying rack and allow them to air dry before reusing.
Cleaning the Power Base
This part in most machines does not get dirty easily. Yet, the Nutribullet’s design necessitates turning the blender cup upside down; spillage is bound to happen.
When cleaning the power base, take the following steps:
- Unplug the Nutribullet from the power source as usual.
- Next, dampen the rag by soaking it in warm water, completely wringing it out, and carefully cleaning its surface and inside.
- Don’t forget to scrape any food or other debris from the blender’s bottom. Citrus cleaners can also help clean it more quickly.
It’s important to remember that you should never totally submerge the power base in water or clean it in the dishwasher.
Furthermore, before reconnecting the power base to the electrical grid, it must be thoroughly dried, either with a dry cloth or in the open air.
Once a week, or whenever food is spilled, you should clean the power base.
How To Clean A Nutribullet’s Gasket?
Most people believe that removing the gasket is required to clean the blade.
Never remove the gasket from the blade. This causes the gasket to come loose, making it less effective for its purpose.
The spacers ensure that your blade is well-sealed. When using NutriBullet, you will have a leaky disaster on your hands if this is loose.
Cleaning the washer is as simple as hand-washing it in warm, soapy water and scrubbing it with a sponge and dish soap. Meanwhile, rubber rings may require a thin brush to clean the inside of the ring properly.
To remove dirt and tough stains, soak them in warm soapy water for around 10 minutes if necessary.
Cleaning Alternative: Mixing Soap and Water
When the parts within the Nutribullet dry, cleaning is a must. In such cases, you will need a solution of soap and water is an efficient approach for cleaning cups and blades. The following is the washing procedure:
- Fill the blender cup up to 2/3 full with soap and water. Lemons, chopped, may also be used.
- Connect the milling blade to the cup by screwing it counterclockwise into the bottom until it is securely fastened.
- Connect the cup to the power base with soap, water, and a milling blade.
- Gently press down on the cup on the power base until the outer blade starts to rotate. For up to 30 seconds, combine soap, water, and lemon.
Can the Nutribullet blade go in the dishwasher? As previously mentioned, the cup, lip rim, and lid are dishwasher safe.
Cleaning the machine is not too difficult. Cleaning the blender helps the product last for a long time and increases the machine’s life.
Thank you for your interest in the article!
Follow our blog to read more blender articles updated daily at: BlendingLovers.com
Taylor Klaus is an expert bartender with 5 years of experience, she’s written over 100 blender tutorials and smoothie recipes. She’s a fan of nutrient-rich puree drinks. She wants to help people have a healthier life.